Ti掺杂对CoCrCuFeMn高熵合金组织结构和耐磨性的影响

doi:10.3901/JME.2020.10.110

机械工程学报 ›› 2020, Vol. 56 ›› Issue (10): 110-116.doi: 10.3901/JME.2020.10.110

扫码分享

Ti掺杂对CoCrCuFeMn高熵合金组织结构和耐磨性的影响

马明星^1,2, 王志新¹, 周家臣¹, 梁存¹, 朱达川², 张德良³

1. 中原工学院材料与化工学院郑州 450007;
2. 四川大学材料科学与工程学院成都 610065;
3. 东北大学材料科学与工程学院沈阳 110819

收稿日期:2019-05-13 修回日期:2019-10-23 出版日期:2020-05-20 发布日期:2020-06-11
通讯作者: 王志新(通信作者),男,1972年出生,博士,教授。主要研究方向为新型金属材料。E-mail:zxwang72@163.com
作者简介:马明星,男,1984年出生,博士,副教授。主要研究方向为新型金属材料。E-mail:manager92@163.com
基金资助:
国家自然科学基金（51271115）和河南省高等学校重点科研（20B430022）资助项目。

Effect of Ti Doping on Microstructure and Wear Resistance of CoCrCuFeMn High-entropy Alloys

MA Mingxing^1,2, WANG Zhixin¹, ZHOU Jiachen¹, LIANG Cun¹, ZHU Dachuan², ZHANG Deliang³

1. School of Materials and Chemical Engineering, Zhongyuan University of Technology, Zhengzhou 450007;
2. College of Materials Science and Engineering, Sichuan University, Chengdu 610065;
3. School of Materials Science and Engineering, Northeastern University, Shenyang 110819

Received:2019-05-13 Revised:2019-10-23 Online:2020-05-20 Published:2020-06-11

摘要/Abstract

摘要： 高熵合金由于具有众多优异性能，有可能突破传统合金的性能极限，被认为是下一代金属材料的发展方向。CoCrCuFeMn作为一种重要的高熵合金体系，目前关于Ti掺杂对其组织结构与性能影响的报道较少。采用熔铸法制备等摩尔比的CoCrCuFeMn和CoCrCuFeMnTi高熵合金，利用XRD、OM、SEM、EDS、显微硬度计和摩擦磨损试验机分别测试Ti掺杂前后对其物相结构、显微组织和耐磨性的影响。结果表明，CoCrCuFeMn由FCC1和FCC2双相组成，Ti掺杂使其物相结构转变成BCC和HCP相的双相组织。两种合金均为典型的树枝晶结构，Cu元素在晶间富集，Mn元素的偏析系数最小。Ti掺杂并未改变合金元素的富集区域，但使所有元素偏析系数降低。Ti掺杂使合金的硬度从219.6 HV提高到693.8 HV，摩擦因数和质量损失率分别从0.57、4.14%降低到0.55、1.28%。Ti掺杂合金硬度和耐磨性的提高主要是由于相转变、固溶强化、细晶强化和内应力降低的综合作用所致。研究成果不仅有助于完善和丰富Ti元素掺杂对CoCrCuFeMn合金性能影响的相关理论，同时也为该合金后续的科学研究和工程应用提供理论支撑。

关键词: 高熵合金, CoCrCuFeMn, 微观组织结构, 耐磨性

Abstract: High-entropy alloys are considered as the development direction of the next-generation metal materials due to its many excellent properties, which may break through the performance limits of traditional alloys. CoCrCuFeMn is as an important high-entropy alloy system. There are few reports on the effect of Ti doping on their microstructure and properties at present. CoCrCuFeMn and CoCrCuFeMnTi high entropy alloys are fabricated by melting-casting method. The phase structure, microstructure and wear resistance for this alloy without and with Ti doping are investigated by XRD, OM, SEM, EDS, microhardness tester and friction-wear tester, respectively. The results show that CoCrCuFeMn alloy has FCC1+FCC2 dual phase structure. The phase structure transforms into BCC+HCP dual phase after Ti doping. Both alloys are typical dendrite structures. The interdendrite region is mainly Cu-rich area, and Mn has the smallest segregation coefficient. After Ti doping, the enrichment region of the alloying elements does not change, but the segregation coefficient decreases for alloy elements. The microhardness increases from 219.6 HV to 693.8 HV after Ti adding, and the average friction coefficient and the mass loss rate decrease from 0.57 and 4.14% to 0.55 and 1.28%, respectively. The improvement of hardness and wear resistance for Ti doping alloy is mainly due to the combined effects of phase transformation, solid solution strengthening, fine grain strengthening and lower internal stress. The research results not only help to improve and enrich the related theory of Ti doping on the properties of CoCrCuFeMn alloy, but also provide theoretical support for their subsequent scientific research and engineering application.

Key words: high-entropy alloy, CoCrCuFeMn, microstructure, wear resistance

中图分类号:

TG156

马明星, 王志新, 周家臣, 梁存, 朱达川, 张德良. Ti掺杂对CoCrCuFeMn高熵合金组织结构和耐磨性的影响[J]. 机械工程学报, 2020, 56(10): 110-116.

MA Mingxing, WANG Zhixin, ZHOU Jiachen, LIANG Cun, ZHU Dachuan, ZHANG Deliang. Effect of Ti Doping on Microstructure and Wear Resistance of CoCrCuFeMn High-entropy Alloys[J]. Journal of Mechanical Engineering, 2020, 56(10): 110-116.

参考文献

[1] YEH J W,CHEN S K,LIN S J,et al. Nanostructured high-entropy alloys with multiple principal elements:Novel alloy design concepts and outcomes[J]. Advanced Engineering Materials,2004,6(5):299-303.
[2] DERIMOW N,ABBASCHIAN R. Solidification microstructures and calculated mixing enthalpies in CoCrCu containing alloys[J]. Materials Today Communications,2018,15:1-10.
[3] LYU Z,LEE C,WANG S Y,et al. Effects of constituent elements and fabrication methods on mechanical behavior of high-entropy alloys:A review[J]. Metallurgical and Materials Transactions A,2019,50(1):1-28.
[4] 马明星,王志新,卢金斌,等. CeO₂掺杂对CoCrCuFeMn高熵合金组织结构与耐磨性的影响[J]. 材料热处理学报,2019,40(9):50-56. MA Mingxing,WANG Zhixin,LU Jinbin,et al. Effect of CeO₂ doping on microstructure and wear resistance of CoCrCuFeMn high-entropy alloy[J]. Transactions of Materials and Heat Treatment,2019,40(9):50-56.
[5] LIU Y Y,CHEN Z,SHI J C,et al. The effect of Al content on microstructures and comprehensive properties in AlxCoCrCuFeNi high entropy alloys[J]. Vacuum,2019,161:143-149.
[6] 李青宇,张航,李涤尘,等. 激光增材制造WNbMoTa高性能高熵合金[J]. 机械工程学报,2019,55(15):10-16. LI Qingyu,ZHANG Hang,LI Dichen,et al. Manufacture of WNbMoTa high performance high-entropy alloy by laser additive manufacturing[J]. Journal of Mechanical Engineering,2019,55(15):10-16.
[7] LUO W Y,LIU Y Z,LUO Y,et al. Fabrication and characterization of WC-AlCoCrCuFeNi high-entropy alloy composites by spark plasma sintering[J]. Journal of Alloys and Compounds,2018,754:163-170.
[8] 谢红波,刘贵仲,郭景杰. Zr元素对AlFeCrCoCuZrx高熵合金组织及腐蚀性能的影响[J]. 材料工程,2016,44(6):44-49. XIE Hongbo,LIU Guizhong,GUO Jingjie. Effect of Zr addition on microstructure and corrosion properties of AlFeCrCoCuZrx high-entropy alloys[J]. Journal of Materials Engineering,2016,44(6):44-49.
[9] YU Y,WANG J,LI J S,et al. Tribological behavior of AlCoCrCuFeNi and AlCoCrFeNiTi0.5 high entropy alloys under hydrogen peroxide solution against different counterparts[J]. Tribology International,2015,92:203-210
[10] 刘玉林,罗永春,赵丹,等. 高熵合金(CoCrFeMnNi)/铜真空扩散连接的界面行为及接头性能研究[J]. 机械工程学报,2017,53(2):84-91. LIU Yulin,LUO Yongchun,ZHAO Dan,et al. Interfacial behavior and joint performance of high-entropy alloy CoCrFeMnNi and pure Cu joints obtained by vacuum diffusion welding[J]. Journal of Mechanical Engineering,2017,53(2):84-91.
[11] OTTO F,YANG Y,BEI H,et al. Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys[J]. Acta Materialia,2013,61(7):2628-2638.
[12] DU W D,LIU N,ZHOU P J,et al. Microstructural evolution,phase selection and properties of CoCrCuFeMnxNi high-entropy alloys[J]. International Journal of Materials Research,2018,109(9):844-850.
[13] OH S M,HONG S I. Microstructural stability and mechanical properties of equiatomic CoCrCuFeNi,CrCuFeMnNi,CoCrCuFeMn alloys[J]. Materials Chemistry and Physics,2018,210:120-125.
[14] 马明星,朱达川,王志新,等. AlCoCrCuFe高熵合金的组织结构与摩擦磨损性能[J]. 工程科学与技术,2018,50(4):208-213. MA Mingxing,ZHU Dachuan,WANG Zhixin,et al. Microstructure and wear resistance of AlCoCrCuFe high-entropy alloy[J]. Advanced Engineering Sciences,2018,50(4):208-213.
[15] TAKEUCHI A,INOUE A. Classification of bulk metallic glasses by atomic size difference,heat of mixing and period of constituent elements and its application to characterization of the main alloying element[J]. Materials Transactions,2005,46(12):2817-2829.
[16] 杨海滨,邹广田,李明辉. 室温下Fe79Ni19Mn2合金的压致bcc→hcp相变[J]. 吉林大学自然科学学报,1992(2):64-69. YANG Haibin,ZOU Guangtian,LI Minghui. Pressure induced bcc→hcp phase transition of Fe79Ni19Mn2 alloy at room temperature[J]. Acta Scientiarum Naturalium Universitatis Jilinensis,1992(2):64-69.
[17] 陈奇志,褚武扬,颜庆云,等. 有序合金中FCC→HCP相变温度内出现的缺陷[J]. 金属学报,1999,35(1):1-5. CHEN Qizhi,CHU Wuyang,YAN Qingyun,et al. The defects formed before FCC→HCP transition in the intermetallic compound[J]. Acta Metallurgica Sinica,1999,35(1):1-5.
[18] 陆海峰,缪强,梁文萍,等. 不同温度对TC4-DT钛合金摩擦磨损性能的影响[J]. 南京航空航天大学学报,2016,48(1):29-34. LU Haifeng,MIAO Qiang,LIANG Wenping,et al. Effect of different temperatures on tribological properties of TC4-DT Alloy[J]. Journal of Nanjing University of Aeronautics & Astronautics,2016,48(1):29-34.
[19] 王志伟,闫洪,熊俊杰. Sr变质对ADC12合金摩擦磨损性能的影响[J]. 中国有色金属学报,2016,26(5):1075-1083. WANG Zhiwei,YAN Hong,XIONG Junjie. Effect of Sr modification on friction and wear properties of ADC12 alloy[J]. The Chinese Journal of Nonferrous Metals,2016,26(5):1075-1083.

Ti掺杂对CoCrCuFeMn高熵合金组织结构和耐磨性的影响

Effect of Ti Doping on Microstructure and Wear Resistance of CoCrCuFeMn High-entropy Alloys

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	李青宇, 张航, 李涤尘, 王兴理想, 陈子豪, 黄胜. 激光增材制造WNbMoTa高性能高熵合金[J]. 机械工程学报, 2019, 55(15): 10-16.
[2]	周佳楠, 张国栋, 郑飞, 杨辉, 梅青松. Cr13不锈钢CMT堆焊金属表面高压滚压层结构与性能研究[J]. 机械工程学报, 2017, 53(8): 68-74.
[3]	石岩, 李云峰, 刘佳, 袁振玉. 高压油泵凸轮轴激光增材制造梯度耐磨层研究^*[J]. 机械工程学报, 2017, 53(6): 80-87.
[4]	刘玉林, 罗永春, 赵丹, 张国庆, 康龙. 高熵合金(CoCrFeMnNi)/铜真空扩散连接的界面行为及接头性能研究[J]. 机械工程学报, 2017, 53(2): 84-91.
[5]	宗琳, 李荣广, 张小玲. 激光熔覆Fe-Ti-V-C合金微观组织与磨损性能^*[J]. 机械工程学报, 2017, 53(2): 67-73.
[6]	徐国建, 杨文奇, 杭争翔, 刘祥宇, 迟海龙, 欧雪松. Stellite-6+VC混合粉末激光熔覆性能的研究[J]. 机械工程学报, 2017, 53(14): 165-170.
[7]	张国栋, 杨辉, 王麒瑜, 张雅芝, 李正刚, 黄旭东, 廖运生. 铁素体不锈钢激光熔覆层组织和性能研究[J]. 机械工程学报, 2016, 52(12): 37-45.
[8]	赵彦华、孙杰、李剑峰. KMN钢激光熔覆FeCr合金修复层组织性能及耐磨、耐蚀性研究[J]. 机械工程学报, 2015, 51(8): 37-43.
[9]	李小强;陈火金;李子阳;屈盛官;赖燕根. WC增强Fe-2Cu-2Ni-1Mo-1C粉末冶金钢的制备及其耐磨性能研究[J]. , 2013, 49(18): 57-62.
[10]	王清宝;史耀武;栗卓新;王立志;李侠;肖静. Cr5系堆焊合金碳、铬过渡形式对高温磨损性能影响的研究[J]. , 2012, 48(4): 78-84.
[11]	魏德强;信卫坡;王荣. 电子束扫描对铝合金表面强化层的影响[J]. , 2010, 46(16): 125-130.
[12]	冷永祥;孙永春;孙鸿;陈俊英;王进;黄楠. 沉积温度对脉冲真空弧源沉积类金刚石薄膜性能的影响[J]. , 2004, 40(7): 20-23.
[13]	花银群;杨继昌;杨兴华;蔡兰;张永康. 激光淬火+冲击复合强化处理45钢的试验研究[J]. , 2004, 40(2): 42-44.
[14]	徐承俊;黄微;范迅;耿凤秋. 复合齿形齿轮的耐磨性研究[J]. , 2001, 37(5): 97-99，1.
[15]	李长虹;何庆复. 耐高温磨损的合金钢导辊及高温耐磨性能研究[J]. , 2001, 37(4): 86-88.